How to set BIOS HD mode to AHCI?

January 12, 2015, 3:16 pm

≫ Next: Multimedia Audio contrlloler is not installed properly due to an exclamation mark in front of it.

≪ Previous: I need repair pst in my mail faster

$

0

0

Hi,

While there is no installation of Windows on my local hard drive, I have tried to install :

• Microsoft Windows XP Professional Edition Version 5.1. 2600 Service Pack 1
  Build 2600
• Microsoft Windows XP Professional Edition Version 5.1. 2600 Service Pack 2
  Build 2600
• Microsoft Windows XP Professional Edition Version 5.1. 2600 Service Pack 3
  Build 2600

However, in each time, I was faced this error below:

Blue Screen error( Stop Code: 0x0000050(0xB25500c2,0x00000000,0x00000000)



That Blue Screen error showed me while Windows Setup was copying the files to
prepare installing Windows XP with any SP.

I didn't install any new hardware. Also, there are no settings, such as
BIOS HD mode in the BOIS to be set to AHCI.

I was told: 'The usual suspect here is BIOS HD mode is set to AHCI and not Compatibility, but as you said no such options exist and I suspect they would not in the BIOS considering its age. This is often reflected as a 0x7B issue when Windows uses Int-13H on boot via installation method.'
 

Although I have tried to install Windows XP on three computers of mine below, I ended up with the same blue screen error. All of my compyters do not have a BIOS HD mode be set to AHCI.

• HP Laptop with core i5, 2GHz, 6GB of RAM, 1GB of Graphics Card Memory.
• Desktop Computer with Intel P 4 3GHz, and 512MB, Craphics Card with 256MB of RAM.
• Desktop Computer with Intel P 3 1GHz, and 256MB of RAM. Graphics Card with 128MB of RAM .

---

A man should convert his anger and sadness into strength to continue living in this life.

---

Multimedia Audio contrlloler is not installed properly due to an exclamation mark in front of it.

January 12, 2015, 6:03 pm

≫ Next: Exception Processing message c0000013 Parameters 75b6bf7c 4 75b6bf7c 75b6bf7c

≪ Previous: How to set BIOS HD mode to AHCI?

$

0

0

Hi,
I have a Windows XP SP3(32Bit) installed on a Desktop Computer with a PIII processor, and 512MB of RAM.

My Desktop Computer with P 4 doesn't have any access internet since there is no network adapter installed. As a result, I would not be able to run the Intel  Audio Card Reader a web-based applet that identifies my Audio Card and finds the latest audio driver for my Audio adapter.

I have Multimedia Audio contrlloler driver installed improperly since an exclamation mark is shown in front  of it in the device manager.

This is Hardware ID (PCI\VEN_8086&DEV_24D5&SUBSYS_97611849&REV_02).

I have tried to download the driver from here:

However, I don't know which one of them I should download since there are quite a lot of them, and there aren't classified as to 32-Bit, and 64-Bit versions of Windows Systems.

Thus, could you please help me to decied which one I could choose.

---

A man should convert his anger and sadness into strength to continue living in this life.

Exception Processing message c0000013 Parameters 75b6bf7c 4 75b6bf7c 75b6bf7c

August 23, 2009, 12:09 am

≫ Next: Print screen doesn't work

≪ Previous: Multimedia Audio contrlloler is not installed properly due to an exclamation mark in front of it.

$

0

0

Every time I logg on to my computer, I get this message:  Exception Processing message c0000013 Parameters 75b6bf7c 4 75b6bf7c 75b6bf7c


HOW CAN I FIX THIS ERROR????

Print screen doesn't work

January 14, 2015, 2:34 am

≫ Next: MSconfig - All applications disabled. Now Black Screen with Cursor

≪ Previous: Exception Processing message c0000013 Parameters 75b6bf7c 4 75b6bf7c 75b6bf7c

$

0

0

Hi team

I have problem with my print screen bottom on laptop keyboard I tired this way ( Windows+ctrl+print screen) and ( Fn+windows+print screen) but still it doesn't work what can I do now please help me 

meanwhile, my windows in 8.1 and my laptop model is asus K451LB 

thank you

MSconfig - All applications disabled. Now Black Screen with Cursor

January 15, 2015, 6:11 am

≫ Next: Folder Name Are not visible in C Drive (Resolved)

≪ Previous: Print screen doesn't work

$

0

0

I was working on my girlfriends computer. She had downloaded a lot of viruses. I was attempting to boot her computer with the applications disabled. I had hit Disable all when I started to go through the applications to see if they were trust worthy. Then it happened... I stepped away from the computer and my girlfriend hit restart with all the applications disabled. After rebooting the computer and log in the screen is black with only a cursor. I tried pressing Ctrl + alt + delete. But, an error pops up saying that it was unable to display. I also tried hitting the windows key, right clicking but it was no good.  I am able to boot the computer in safe mode. How can I change the start up application for normal start up from safe mode. Or, is there another way I should go about this. 

Folder Name Are not visible in C Drive (Resolved)

November 22, 2011, 11:42 pm

≫ Next: Question about Windows Services

≪ Previous: MSconfig - All applications disabled. Now Black Screen with Cursor

$

0

0

HI ,

I have two Desktop PC & both have Win Xp Operating system.In both of them  C Drive folder name are not showing,  but in other drive folder name are showing

Please help me how to resolve this issue.

---

Rakesh Kumar

Question about Windows Services

January 16, 2015, 5:07 am

≫ Next: where can i download the latest iso image of windows xp

≪ Previous: Folder Name Are not visible in C Drive (Resolved)

$

0

0

I've been trying to cut corners on an XP machine. Since it doesn't need network connectivity, I've disabled networking related services. However, I was wondering if System-level (Start type 0x1) services are safe to disable as well (located under SYSTEM\CurrentControlSet\Services). Specifically, IPSEC, NETBIOS, Tcpip, and TermDD (these are the exact key names).

I have disabled these services, and didn't have any issues booting. But I haven't done anything beyond that (such as long-term affects/unintended side effects).

where can i download the latest iso image of windows xp

December 26, 2014, 11:02 pm

≫ Next: Account Logging in problem

≪ Previous: Question about Windows Services

$

0

0

where can i download the latest iso of the windows xp with more features. it was the best os ever and fastest too. and i want the xp i have the cd also purchased by microsoft and key also but the cd has crashed but the key isn't crashed. i am bored of windows vista, windows 7 and windows 8. can you please give me the download link please

---

Account Logging in problem

January 2, 2015, 3:02 am

≫ Next: copy and paste not working

≪ Previous: where can i download the latest iso image of windows xp

$

0

0

one day when I tried to log in to my user account in windows xp sp3, a pop-up screen came telling that "windows can't load your local profile, so windows will load a temporary profile." I clicked OK and it went into my account there i found the following problems:

• My Documents did not had any files only my videos and pictures folder .
• my desktop had only installed programs icons and not files.
•  start menu was completely modified with only windows programs but all programs had my installed files.
• D:,E:,F: was safe

please give me a solution that will revert all problems, even system restore doesn't has a restore point! help me! 

copy and paste not working

December 3, 2011, 11:48 pm

≫ Next: Default VGA driver can let me increase resolution between '800x600' to '1024X 768'?

≪ Previous: Account Logging in problem

$

0

0

2 days ago I noticed that my copy and paste functions stopped working! I am using win xp home sp3 and I do NOT use any remote file sharing or remote apps. No new programs have been installed or removed in over a month.

I have tried using the keyboard shortcuts crtl+c and crtl+v, right click copy and paste which doesn't work and neither does the copy or paste function under the edit menu. when I highlight text I can use copy ( enabled with black text) in the edit menu, right click and hit copy or do a crtl+c but when I go to paste the text into any text document regardless if using keyboard shortcut crtl+v, right click or the edit menu, the paste function is not enabled ( grayed out)

These functions are not working in any document program on my PC nor do they work with paint shop pro or photo shop when I try to copy an image into my work image.

if there any way to fix this? I need my copy and paste functions to work again!!!

I have tried just about everything to get this to work .. restoring to the day before the issue started didn't help. My fiance is a PC tech and even he couldn't get it to work even after checking to make sure the clipboard was not full ( it was empty), reformatting is not an option as I need my PC for my job and copy and paste is a big part of my job as a graphic designer.

Default VGA driver can let me increase resolution between '800x600' to '1024X 768'?

January 18, 2015, 6:18 pm

≫ Next: Multimedia Audio Controller, and Video Controller(VGA compatible) are missing on Windows XP(32Bit) SP3

≪ Previous: copy and paste not working

$

0

0

Hi,

I was told that the initial VGA is an standard, 800x600 or similar, only gives me the option to show image but not some other possibilities like external display, clone display and those stuffs.The specific VGA (FX 5200) driver, give to your rig the "possibility" to address all the image process to an specific device, in this case, the FX 5200 and add some extra functions like external display (at different resolutions), clone display, extend display...and those stuffs.

However, I noticed that while using the default VGA driver, then I could increase 'resolution from '800X600' to 1024x768 Pixels. Also, the 'colour quality' to 32Bit or 16Bit, although it is intial, standard VGA, I could change the resolution.

Thus, my questions are:

First:  what benefit is there from instlling the driver of the default VGA as long as I can change the screen resolution into '1024X 768' while using default VGA driver, which means that icons, and display would be OK??

Second:  With using a default VGA driver on any Computer, there are only  '800x600' to '1024X 768'? (I.e. The resolution of all default monitor can be only between   800x600 and '1024X 768'?

---

A man should convert his anger and sadness into strength to continue living in this life.

Multimedia Audio Controller, and Video Controller(VGA compatible) are missing on Windows XP(32Bit) SP3

January 19, 2015, 5:15 pm

≫ Next: How to install the driver of the 'SCSI and RAID Host Controller'

≪ Previous: Default VGA driver can let me increase resolution between '800x600' to '1024X 768'?

$

0

0

Hi.

I have two Windows XP installations:

• Windows XP SP2(32Bit) which is old and it seems it infected by some viruses.
• I have installed another fresh clean Windows XP(32Bit) SP3. However, I have two devices not detected well by Windows XP.













According to the screen shots above, then

The vendor ID of Multimedia Audio Controller  is 8086 and the device ID is24D5.

The vendor ID of Video Controller  is 8086 and the device ID is2572.



I AM EXPECTING THAT KNOWING THE VENDOR ID AND THE DEVICE ID WILL LET ME QUICKLY FIND THE APPROPRIATE  DRIVER. HOWEVER, I COULDN'T FIND THE APPROPRIATE DRIVER.

Thus, could you please help me to find them?



I have tried installing a soundMAX card  driver, however, I found this error.











I have checked the other Windows XP SP2(32Bit) which is oder installed, and it seems it infected by some viruses.

However, the Multimedia Audio on that Windows is installed well. As here: I only posted these screen shots to show what kind of device is Multimedia Audio Card











The motherboard model is:



Belarc Advisor Computer Profile



Operating System System Model Windows XP Professional Service Pack 3 (build 2600) Install Language: English (United States) System Locale: Arabic (Yemen) Installed: 22/03/2013 12:03:16 ص Boot Mode: BIOS (Secure Boot not supported) Enclosure Type: Desktop Processor <sup>a</sup> Main Circuit Board <sup>b</sup> 3.00 gigahertz Intel Pentium 4 16 kilobyte primary memory cache 1024 kilobyte secondary memory cache 64-bit ready Hyper-threaded (2 total) Board: 775i65G. Bus Clock: 200 megahertz BIOS: American Megatrends Inc. P3.00 03/20/2007 Drives Memory Modules <sup>c,d</sup> 39.99 Gigabytes Usable Hard Drive Capacity 29.48 Gigabytes Hard Drive Free Space COMPAQ CD-ROM LTN486S [Optical drive] 3.5" format removeable media [Floppy drive] WDC WD400BB-75DEA0 [Hard drive] (40.00 GB) -- drive 0, rev 05.03E05, SMART Status: Healthy 504 Megabytes Usable Installed Memory Slot 'DIMM0' has 512 MB Slot 'DIMM1' is Empty Local Drive Volumes c: (NTFS on drive 0) * 20.98 GB 14.16 GB free d: (NTFS on drive 0) 19.01 GB 15.33 GB free <center> * Operating System is installed on c: </center> Network Drives None discovered Users <small>(mouse over user name for details)</small> Printers local user accounts last logon عايض لرضي 19/01/2015 10:59:17 م (admin) local system accounts Administrator never (admin) Guest never HelpAssistant never SUPPORT_388945a0 never <center>Marks a disabled account;   Marks a locked account </center> Controllers Display Standard floppy disk controller Intel(R) 82801EB Ultra ATA Storage Controllers Primary IDE Channel [Controller] Secondary IDE Channel [Controller] None discovered Bus Adapters Multimedia Intel(R) 82801EB USB Universal Host Controller - 24D2 Intel(R) 82801EB USB Universal Host Controller - 24D4 Intel(R) 82801EB USB Universal Host Controller - 24D7 Intel(R) 82801EB USB Universal Host Controller - 24DE Intel(R) 82801EB USB2 Enhanced Host Controller - 24DD None discovered Virus Protection<small>[Back to Top]</small> Group Policies Norton AntiVirus Version 18.1.0.37     Virus Definitions Version Not Up To Date     Realtime File Scanning On None discovered Communications Other Devices ↓ Realtek RTL8139 Family PCI Fast Ethernet NIC Status: Cable unplugged Dhcp Server: none responded Physical Address: 00:19:66:1F:F7:54 USB Human Interface Device Standard 101/102-Key or Microsoft Natural PS/2 Keyboard HID-compliant mouse USB Root Hub (5x) USB Storage Use in past 30 Days<small>(mouse over last used for details)</small> Hosted Virtual Machines<small> (mouse over name for details)</small> Last Used SanDisk Cruzer Blade, s/n 4C532000020502112303, rev 2.01 19/01/2015 09:32:57 م* USB 2.0 USB Flash Drive, s/n 59309e92e21612, rev 0.00 09/01/2015 12:29:17 ص* <center>* Possibly used again before the reboot following this time.</center> None discovered See your entire network map... click for Belarc's System Management products 



---

A man should convert his anger and sadness into strength to continue living in this life.

How to install the driver of the 'SCSI and RAID Host Controller'

January 19, 2015, 6:14 pm

≫ Next: Windows XP SP3 (2015) Correct password is incorrect when open LAN share

≪ Previous: Multimedia Audio Controller, and Video Controller(VGA compatible) are missing on Windows XP(32Bit) SP3

$

0

0

Hi,
I have two Windows XP(32Bit) installations:
•Windows XP SP2(32Bit) which is old and it seems as if it is infected by some viruses.
•I have installed another fresh clean Windows XP(32Bit) SP3. However, I have found that there is no category named with ''SCSI and RAID Host Controller'. However, when checking out the old version of Windows XP, I found  'SCSI and RAID Host Controller' is there. (Screen shot below)

The new Windows XP(32Bit) SP3, there is no 'SCSI and RAID Host Controller'

My motherboard is:

My Desktop Computer(Intel P 4, 512MB of RAM, and Graphics Card  with 256MB of RAM.

]I am seeing that most computer doesn't has the scsi / raid controller . in the old Windows XP on my computer that SCSI and RAID controller exists, and it it has not  a yellow mark on it.
When I installed  a new windwos XP 32Bit SP3, no SCSI/RAID in divice manager .
My computer sound on new Windows XP doesn't work , however, on old Windows XP SP2 works well. I have a buitl-in  sound card. SCSI and RAID controller category in the device manager on the old Windows xp SP2 is realted to sound card,I don't think.

Thus, What drivers would let the 'SCSI and RAID Host Controller' added in the device manager?

---

A man should convert his anger and sadness into strength to continue living in this life.

Windows XP SP3 (2015) Correct password is incorrect when open LAN share

January 20, 2015, 12:31 am

≫ Next: Auto switch from LAN to WIFI

≪ Previous: How to install the driver of the 'SCSI and RAID Host Controller'

$

0

0

Hello,

I was install windows XP SP3 with latest update. After installing, I want to open an excutable or program on LAN network sharing and then the pop up login access LAN with guest user disabled textbox is showing as normally, but when I type the password correctly the windows XP wont to open share besides the password is really correctly.

- I have set date and time correctly

- I have disabled firewall.

Whats wrong, there a services can I starting?

here is preview logon and windows xp SP3 latest :

Thank you,

Really hope your answer.

Auto switch from LAN to WIFI

January 20, 2015, 1:30 am

≫ Next: Group policy error: Failed to open group policy object on this computer.

≪ Previous: Windows XP SP3 (2015) Correct password is incorrect when open LAN share

$

0

0

I am looking for some software or a way to auto switch from LAN to WiFI if there no internet connection.

This history of this is we have a XP machine that runs a process and its just left on for this and nothing else, with no keyb or mouse connected and we just remote to it if needed.  Our internet connection has issues and quite often drops out, but local LAN obviously stays up, we have a WiFi connection to another site opposite that is ok, question is does anyone know any software that will for example ping a external host every so often and if there is no response will auto switch from LAN to WiFi connection automatic.

Thanks. 

---

Group policy error: Failed to open group policy object on this computer.

May 20, 2010, 4:33 am

≫ Next: KB2833941 - continuous update.

≪ Previous: Auto switch from LAN to WIFI

$

0

0

Hi all,

I received this message when i tried to look at the local group policy setting on one of my machines (Windows XP SP3), which is joined in my domain.

"Failed to open group policy object on this computer. You may not have appropriate rights.

Details:

Unspecified error."

note that I am local admin.

It's all started when I was troublshooting WSUS connectivity and i looked at the WinsdowsUpdate.log, the WSUS server was <Null> & WSUS status server <Null>, I tried to force the domain GP by using GPupdate /force, it went fine and asked to log off, but nothing changed in the WindowsUpdate.log still <Null>. Then i tried to look at the local policy setting.

I searched the internet nothing related to my case.

Thanks in advance for advising.

Mohammed Adel

KB2833941 - continuous update.

July 26, 2013, 6:18 am

≫ Next: Blue screen .... Shut down button not working.. Winxp

≪ Previous: Group policy error: Failed to open group policy object on this computer.

$

0

0

KB2833941 keeps loading (sucessfully) every time the XP computer is updated.

Any solution to this problem besides hiding the update?

Thanks,

Andy

 

Blue screen .... Shut down button not working.. Winxp

January 22, 2015, 9:48 pm

≫ Next: gurunivas

≪ Previous: KB2833941 - continuous update.

$

0

0

Hi Community...
Great day to you all..
I have windows xp old pc (I know its already no supported yet i cant switch to another os).. Im using nod 32 4.2 antivirus.. (No any other antivirus mcafee or anything).. Its old one and working without issue until recent issue.. I had two bluescreens and I have attached them ..and the main problem is shutdown button not working.. I have to use pc hard shutdown button or power off to shutdown or else to use shutdown -s -f -t 00 command... And also some times it got stuck while booting.. it sticks at bios boot screen.... The pc is dell optiplex 330 desktop.. Windows XP sp3 is the service pack..

I have collected the dump and system information according to this wiki.. http://answers.microsoft.com/en-us/windows/wiki/windows_other-system/blue-screen-of-death-bsod/1939df35-283f-4830-a4dd-e95ee5d8669d

I wish to know What is causing the issue so that i can replace hardware or reinstall problematic software or anything.. I do have fair understanding of computers.. but not know how to analyze and find the issue regarding blue screens

Here are the two dumps and system info file.. https://drive.google.com/file/d/0BwjI8poUeE9OYlZGc2RlMTRhVHc/view

Any help would be greatly appreciated.... Please guide me...

gurunivas

January 23, 2015, 6:02 am

≫ Next: Installing Windows XP with a pen drive

≪ Previous: Blue screen .... Shut down button not working.. Winxp

$

0

0

gurunivas i am use for home i am not bisnasse

Installing Windows XP with a pen drive

January 24, 2015, 4:08 am

≫ Next: 'SCSI', RAID', and even AHCI are not concrete (physical) hardware parts

≪ Previous: gurunivas

$

0

0

Hello all, 

I am trying to install Windows XP in an old laptop, and i must do it using a drive pen cause the laptop doesn't have a disk reader. 

So I already have a program which enables me to install it via pen drive but it does not recognize the DOS system...

How is supposed to be the "ending" of this program??? I currenlty have one that ends with .ISO and another one i just got is an .exe but none of those are accepted by the pen drive as a DOS program... :| where can i download this sorcery?! i am trying to do this since i woke up :| 

can someone please be kind and help me :)

thanks!

Diana